Diamond drilling technology and key benefits

2024 Author: Howard Calhoun | [email protected]. Last modified: 2023-12-17 10:16

Every year, diamond drilling and concrete drilling are replacing other technologies. For example, a puncher has many disadvantages, unlike this method. These are vibrations, high noise levels, etc. Most often, such drilling is used during construction or repair work. Let's talk about this topic and see what are the pros and cons of diamond drilling.

Diamond drilling: general points

The main difference is that when using this technology, shock loads are completely absent, as well as excessive vibration and noise. To achieve high results, they use modern technologies (diamond drill, special equipment with noise damping). During the construction of a building, it is often necessary to make a deep hole in the concrete. If you use jackhammers, it is very easy to damage the structure, and this is fraught with consequences. Diamond drilling and drilling are characterized byhigh performance, which allows you to perform large amounts of work. But these are not all the advantages that I would like to talk about. Let's talk about the advantages, which are many in this technology.

Diamond hole drilling benefits

One of the main advantages is that the customer can get the most accurate hole sizes. This is very important, especially when carrying out installation work of a high level of complexity. The absence of dust is another rather important factor. Sometimes hydraulic suppression is used, that is, ordinary water. As noted above, the non-impact drilling method makes it possible to achieve an almost complete absence of noise. The treated metal and concrete structures do not experience destructive dynamic loads, which prolongs the service life. Sometimes, using the same puncher or jackhammer, it is almost impossible to make a hole for communications (electricity, water supply) in a building, but this is not a problem at all for installing diamond drilling. Moreover, the hole will be perfectly even and smooth, which is undoubtedly important.

About technology

Diamond drilling of concrete is a complex process, during which expensive equipment is used, so this technology is considered unique in its own way. It is as follows. At the first stage, the future holes are marked. At this time, their depth and diameter, as well as the angle of inclination, are determined. Next comes the drilling process itself, which lasts only 10-20 minutes, depending onon the conditions in which the work is performed, and the size of the hole. Thanks to the built-in cooling system, the unit does not overheat, which allows you to make work uninterrupted and get everything done in one go. Once again, you should pay your attention to the fact that the diamond crown is a high-strength product, so it can drill a hole in any metal structure.

About the technique used

The process itself is quite simple, but it involves the use of special expensive equipment. In most cases, this is a diamond core bit and a special drilling rig. The device of the machine is quite simple. This includes a hydraulic drilling device. As you know, the use of a cylinder with liquid, that is, hydraulics, allows you to achieve maximum accuracy and smoothness in obtaining holes. Sometimes an electric motor is used. When it comes to asph alt repair, two-stroke internal combustion engines (ICE) are most often used. When electric drilling rigs are used, both single-phase and three-phase rigs are selected. The former are more preferable from a technical point of view, therefore they are used more often. Typically, the units are equipped with an air cooling system, their power is about 3 kilowatts. As for three-phase installations, they are also used, but they are large and operate from a 380V network, which is available only at construction sites.

Conclusion

Today most often thistechnology for obtaining high-quality, precise and smooth holes is used to install split systems. You can also get anchor holes of almost any size in any foundation. A high-quality diamond drill allows you to get holes with a diameter of more than 200 millimeters. The price of such equipment can be about 100,000 rubles. It is worth noting that the resulting hole does not require further processing, that is, grinding, adjustment, etc. All this saves not only money, but also time, as well as the effort of both the customer and the contractor. Such drilling rigs work both in open and closed premises. The almost complete absence of noise makes it possible to use drilling in residential buildings during repairs or reconstruction. That, in principle, is all that can be briefly told about this method of obtaining cylindrical holes of various depths and diameters. Of course, the high cost pays off with quality, and this is an indisputable fact.